XPE SMD LED 3535 UV LED 430nm

• Customization: Available
• LED Packaging Type: Chip
• Chip Material: AlGaInP
• Model NO.: S3535UV-430NM-3W
• Beam Angle: 120°
• Emitting Color: UV
• IP Rating: IP33
• Base Material: Copper
• LED Chips: Sanan
• Power: 3W
• Life: 30000h
• Certification: RoHS, CE
• Voltage(V): 3-3.6V
• Wavelength: 425-435nm
• Current: 350-700mA
• Warranty(Year): 1 Year
• Storage Temperature(ºC): -40° -- 85°
• Package: 1000PCS/Roll
• ESD Sensitivity: 2000V Hbm
• Transport Package: Carton
• Specification: 3.5*3.5*2mm
• Trademark: RZXLED
• Origin: China
• Production Capacity: 100000000/Week
• Package Size: 2.00cm * 2.00cm * 1.00cm
• Package Gross Weight: 0.001kg

Product Description

Product Description

Item	S3535UV-430NM-3W
Brand Name	RZXLED
Power	3W
Voltage	3-3.6V
Viewing Angle	120°
Wavelength	425-435NM
Forward Current	350-700MA
ESD Sensitivity	2000V HBM

 

Package Dimensions

(1)The label on the minimum packing unit shows ; Part Number, Lot Number, Ranking, Quantity.
(2) Keep away from water,moisture in order to protect the LEDs.
(3)The LEDS may be damaged if the boxes are dropped or receive a strong impact against them. soprecautions must be taken to prevent any damage.

Application&Feature

 

Application

Industrial Curing	Printing
Nail Curing	Counterfeit Detection
UV mosquito Trap	UV Sterilization System
UV Photo-catalyst	UV Sensor Light

Feature

Dimension 3.5mm×3.5mm×2mm	RoHS compliant
Wide viewing angle : 120°	Soldering Temperature

PACKAGING

Note:
1.The label on the minimum packing unit shows;Part Number,Lot Number,Ranking,Quantity
2.Keep away from water,moisture in order to protect the LEDs
3.The LEDs may be damaged if the boxes are dropped pr receive a strong impact against them.soprecautions must to taken to prevent any damage.

Reliability Test

Operating Diagram

Use forceps or other appropriate tools grip along the side surface of component.

Do not touch the silicone surface. It may damage the internal circuitry of the LED.
Do not stack soldered LED, it may cause scratching of LED and silicone damage leading to dead LED 

Do not make contact with thinner, Trichloroethylene, acetone, sulfide, sodium ion and acid,alkali, Salt and other substances. These materials will cause oxidation of silver plating andvulcanization of phosphor leading to color fading and reduction of brightness conditions.

Notes

Packaged LED material is silicone nature, therefore, LED has is a soft and flexible surface. Although characteristics of silicone is to reduce thermal stress, but it is more susceptible to mechanical damage to the external forces applied on the surface. Pressure affects the reliability of light emitting diodes. In such circumstances, the assembly of organic silicon encapsulated LED products must comply with the appropriate measures to deal with. Avoid any pressure applied to any part of the LED and use pneumatic nozzle. Otherwise it may lead to reduction in reliability, and impact of its life to the LED.
The temperature control
Product light foot temperature under 75 ºC which shall be controlled.
Reflow soldering instructions
1.Reflow soldering is recommended to the use of clean free flux, and in accordance to the reflow curve. Maximum number of soldering is limited .
2.hen soldering, do not exert pressure during heating process.
Soldering
1.When manual soldering iron is used, it is recommended to use 20W anti-electro static soldering iron, soldering temperature must be kept below 360 ºC / 3 seconds, 1Time soldering only.
2.Do not mix different BIN materials on the same board, otherwise it will cause LED color Variation.
Repair
When repairing light-emitting diodes, it is advised to confirm the light emitting diode will be damaged, the repair process should avoid contact with the colloid surface, use of soldering iron should be according to following diagram.
Clean
Recommend the use of pure alcohol to clean, wash and wipe or dipping no more than 1 minutes after soldering. When different solvents are used for cleaning, make sure that solvents do not damage the light emitting diode packaging.
Potting
1.The use of silicone rubber (plastic glass) for potting, it is recommended the use of alcoholic encapsulating Material.
2.When deoximation neutral potting material is used, make sure that the potting curing process in well-ventilated. . Do not perform sealing assembly of Light Emitting Diodes before potting is completely cured and setting process is completed. This will result in the silver layer oxidation and luminous color fades, light degradation and even dead LED.
3.Prohibit the use of acetic acid type (acidic) silicone rubber potting materials.
4.It is recommended that small quantity samples are made for potting test, Room temperature light test of 168H confirming no abnormality before mass products.
5.When there is change in potting material, please make samples to confirm whether there is erosion reaction. Take 5-10 grams of potting material and 10-20 pcs in a 100ml sealed containers for 168H confirm whether there is abnormality.
Driving method
(A)Recommended circuits.
(B)Each LED may appear inconsistent brightness, it is a result of the IV curve.
Static electricity
All employees have direct contact with LED for all processes (production, testing, packaging, etc.) must perform all preventive and eliminating static electricity measures.
1.Workshop floors to use of the anti-static flooring and grounding, anti-static work bench, when charged material is in contact with low resistance metal surface, due to acute discharge, possibility of product failure is very high, so the requirements of the bench and any contact.with the products should have surface resistance of 106-109Ω table mats.
2.Production machines such as: tin furnace, reflow soldering, SMT equipment, electric soldering iron, and testing equipment need to be grounded, grounded AC impedance less than 1.0 ohm. Prone to static electricity environment and equipment must be installed ion fan. During working process, operators to wear anti-static clothing, wrist strap, gloves, and etc., When handling, hold the insulated part of the product as much as possible.
3.For packaging of LED, anti-static component boxes, packaging materials should be use.
4.Keep ambient humidity below 60% RH to avoid air being too dry to generate static electricity.
5.Grounding should be connected to the neutral input line. It should be separated from the lightning grounding. Grounding should be done with anti-static. Heavy gauge copper cable should be connected to a large piece of metal and buried at least 1 meter deep into the ground. All ground cables must be connected together with the main cable.

Company Profile